The Industrial high power Gigabit Ethernet PoE (Power over Ethernet) injector feeds devices according to IEEE 802.3at standard with 10/100/1000MBit/s 1000Base-T Gigabit Ethernet and 35W operating current rsp. alternatively devices according to IEEE 802.3af with 15.4W.
Integrated mounting holes enable wall mounting without additional Panels or mounting on 35mm DIN rail in combination with snap-in elements. In metal case on request available.
|
Technical data |
Product | Industrial Gigabit Ethernet PoE injector 35W high power |
Port(s) electrical | Data input: 10/100/1000MBit/s 1000Base-T Gigabit Ethernet |
PoE ports | Data output: 10/100/1000MBit/s 1000Base-T Gigabit Ethernet
current output:
| +56V 35W | Load min./max. | 0.01A / 0.625A | Load reg. | 5 % | line reg. | 1 % | Ripple | 1 % | Noise | 1 % | Noise bandwidth from DC to 20MHz Ripple and Noise measured by paralleling a 0.1uF metalize capacitor on the test point |
|
Pin assignment PoE | Item 114470x1x mode A:
pin 1 2 3 4 5 6 7 8 | data 1000Base A+ A- B+ C+ C- B- D+ D- | data 100Base RX+ RX- TX+
TX- | power
V DC (-) V DC (-) V DC (+)
V DC (+)
|
item 114470x2x mode B:
pin 1 2 3 4 5 6 7 8 | data 1000Base A+ A- B+ C+ C- B- D+ D- | data 100Base RX+ RX- TX+
TX- | power
V DC (+) V DC (+)
V DC (-) V DC (-) |
optional revers power (+/-) on request. |
LEDs | ready: | red | IEEE 802.3at / 802.3af PoE current ok: | green |
|
Housing | 114470xx1 and 114470xx2: Plastic 114470xx3 and 114470xx4: Metal |
Mounting | 114470xx1 and 114470xx3: Wall mountable 114470xx2 and 114470xx4: DIN rail mountable |
Dimensions | LxWxH: 124x74x33mm |
Power requirements | item
1144701xx 1144702xx 1144704xx | input voltage redundant of ~ up to 10V ~ 15V DC 18V ~ 36V DC 40V ~ 60V DC | input current
3.6A @ 12V DC 1.56A @ 24V DC 0.8A @ 48V DC |  |
|
Efficiency | > 80% @ full Load |
Operating temperature | -40°C .. +70°C |
Cooling | Fanless - Free air cooling |
Storage temperature | -40°C .. +85°C |
relative humidity (non condensing) | 5% .. 90% |
Compliance | FCC Class B , EN55032 Class B, IEEE 802.3at, IEEE 802.3af |
Protection | Input protection: Fuse Dual Input Pin and Reverse Protection: No Work Output Short GND Terminal will not damage the power supply and will Auto-Reset |
Overcurrent | item | | 1144701xx 1144702xx 1144704xx | 120% ~ 160% @ 12V DC input F.L. 120% ~ 160% @ 24V DC input F.L. 120% ~ 160% @ 48V DC input F.L. |
|
Country of origin | Taiwan |
Ordering information item |
114470113 | GbE PoE injector IN:10-15VDC IEEE 802.3at mode A metal case |
114470114 | GbE PoE injector IN:10-15VDC IEEE 802.3at mode A Met. DIN rail |
114470123 | GbE PoE injector IN:10-15VDC IEEE 802.3at mode B metal case |
114470124 | GbE PoE injector IN:10-15VDC IEEE 802.3at mode B Met. DIN rail |
114470213 | GbE PoE injector IN:18-36VDC IEEE 802.3at mode A metal case |
114470214 | GbE PoE injector IN:18-36VDC IEEE 802.3at mode A Met. DIN rail |
114470223 | GbE PoE injector IN:18-36VDC IEEE 802.3at mode B metal case |
114470224 | GbE PoE injector IN:18-36VDC IEEE 802.3at mode B Met. DIN rail |
114470413 | GbE PoE injector IN:40-60VDC IEEE 802.3at mode A metal case |
114470414 | GbE PoE injector IN:40-60VDC IEEE 802.3at mode A Met. DIN rail |
114470423 | GbE PoE injector IN:40-60VDC IEEE 802.3at mode B metal case |
114470424 | GbE PoE injector IN:40-60VDC IEEE 802.3at mode B Met. DIN rail |
Ordering information Accessories |
063600001 | DIN rail installation panel for 19 inch distribution rack |
|
Dimensional drawing
|
The product description has been prepared with great care. No liability is accepted for fallacies or errors. Subject to change. |